manualshive.com logo in svg

Applied Innovation AISwitch AI2524, User Manual, Page: 4 / 418

Share
Download
Applied Innovation AISwitch AI2524 User Manual Download Page 4

AI2524 Router User’s Manual

August 1997

2524UM

Copyright Notice

Copyright © 1983-1997 by Applied Innovation Incorporated (AII).  The material discussed in 

this manual is the proprietary property of AII.  AII retains all rights to reproduction and distribution 
of this document.

AISwitch, AISwitch Series 180, and AISwitch Series 130 are registered trademarks of AII.
UNIX is a registered trademark in the United States and other countries, licensed exclusively 

through X/Open Company Limited.  Any other trademarks appearing in this manual are registered 
trademarks of their respective companies.

FCC Warning

The Federal Communications Commission has set limits for emitted radio interference.  The 

AISwitch is constructed with this electromagnetic interference (EMI) limitation in mind.  Th
AISwitch is classified under FCC regulations as a Class A device, that is, a device for use in com-
mercial environments and not in residential areas.  This device has been tested and shown to comply 
with the following FCC rule: Part 15 Subpart J.  Operation of this equipment in a residential are
may cause interference to radio and TV reception, requiring the user to take whatever steps are nec-
essary to correct the interference.

Information is available from the FCC describing possible corrective actions.  For lower EMI 

levels, we suggest using only metal connectors and shielded cables grounded to the frame.

Electrostatic Discharge Warning

Warning: The AISwitch and its peripherals contain electrostatic sensitive components.  Proper 

handling, shipping, and storage precautions must be exercised:

z

Removal and installation of circuit boards must be performed in a static-free en-
vironment.  Tthe technician should wear an anti-static wrist strap and stand on 
an anti-static mat.  Both the wrist strap and mat must be grounded at the same 
point as the AISwitch enclosure.

z

When not in use, circuit boards must be kept in their anti-static plastic bags.

z

Circuit boards must only be removed from their anti-static plastic bags immedi-
ately prior to installation into the AISwitch enclosure.

z

Immediately upon removal from the enclosure, circuit boards must be inserted 
into their anti-static bags.

z

Do not ship or store the electronic circuit boards near strong electrostatic, elec-
tromagnetic, magnetic, or radioactive fields.

Specifications are subject to change without notice.

Applied Innovation Inc.

5800 Innovation Driv

Dublin, Ohio 43016-3271

614-798-2000
800-247-9482

FAX: 614-798-1770

Summary of Contents for AISwitch AI2524



































































































































































































































































































































































































































Reviews:

No comments