manualshive.com logo in svg

Applied Innovation AISwitch AI2524, User Manual, Page: 321 / 418

Share
Download
Applied Innovation AISwitch AI2524 User Manual Download Page 321

Chapter 13: AI2524 Frame Relay Configuration Steps

August 1997

Page 13-5

2524UM

Configuration for Router 2

interface serial 0

ip address 131.108.64.1 255.255.255.0 

encapsulation frame-relay 

keepalive 10

frame-relay map ip 131.108.64.2 43

IPX Routing Example

This example illustrates how to send packets destined for IPX address 
200.0000.0c00.7b21 out on DLCI 102:

ipx routing 000.0c00.7b3b

!

interface ethernet 0 

ipx network 2abc

!

interface serial 0 

ipx network 200 

encapsulation frame-relay 

frame-relay map ipx 200.0000.0c00.7b21 102 broadcast

Configure the 
LMI

Local Management Interface (LMI) autosense enables the interface to 
determine the LMI type supported by the switch and eliminates the 
need to configure the Local Management Interface (LMI) explicitly.

Allow LMI Autosense to Operate

LMI autosense is active in these situations:

z

The router is powered up or the interface changes state to up.

z

The line protocol is down but the line is up.

z

The interface is a Frame Relay DTE.

z

The LMI type is not explicitly configured.

The LMI Autosense Process

When LMI autosense is active, it sends out a full status request, in all 
3 LMI options (ANSI, ITU, Cisco) to the switch. 

Summary of Contents for AISwitch AI2524



































































































































































































































































































































































































































Reviews:

No comments