manualshive.com logo in svg

Applied Innovation AISwitch AI2524, User Manual, Page: 340 / 418

Share
Download
Applied Innovation AISwitch AI2524 User Manual Download Page 340

AI2524 Router Card User’s Manual

Page 13-24

August 1997

2524UM

The 

broadcast

 keyword is required for routing protocols such as 

OSI protocols and the Open Shortest Path First (OSPF) protocol. Se
the 

frame-relay map

 command description in the Wide-Area 

Networking Command Reference for more information about using 
the 

broadcast

 keyword.

Example: IPX Routes over Frame Relay Subinterfaces

This example configures a serial interface for Frame Relay encapsula-
tion and sets up multiple IPX virtual networks corresponding to Frame 
Relay subinterfaces:

ipx routing 0000.0c02.5f4f

!

interface serial 0 

encapsulation frame-relay

interface serial 0.1 multipoint 

ipx network 1 

frame-relay map ipx 1.000.0c07.d530 200 broadcast 

ipx network 2 

frame-relay map ipx 2.000.0c07.d530 300 broadcast

For subinterface serial 0.1, the router at the other end might be config-
ured as:

ipx routing 

interface serial 2 multipoint 

ipx network 1 

frame-relay map ipx 1.000.0c02.5f4f 200 broadcast

Configure Transparent Bridging for Frame Relay

Transparent bridging for Frame Relay encapsulated serial and HSSI 
interfaces is supported on the AI2524 router. Transparent bridging for 
Frame Relay encapsulated serial interfaces is supported on our access 
servers.

You can configure transparent bridging for point-to-point or point-to-
multipoint subinterfaces.

Note:

All PVCs configured on a subinterface belong to the same 
bridge group.

Summary of Contents for AISwitch AI2524



































































































































































































































































































































































































































Reviews:

No comments