manualshive.com logo in svg

Applied Innovation AISwitch AI2524, User Manual, Page: 226 / 418

Share
Download
Applied Innovation AISwitch AI2524 User Manual Download Page 226

AI2524 Router Card User’s Manual

Page 10-2

August 1997

2524UM

3.

Configure the second synchronous serial interface, for example:

Configuring interface Serial 1:

   Is this interface in use? [yes]:

   Configure IP on this interface? [yes]:

   Configure IP unnumbered on this interface? [no]:

     IP address for this interface: 172.16.74.2

     Number of bits in subnet field [8]:

     Class B network is 172.16.0.0, 8 subnet bits; mask is

     255.255.255.0

   Configure AppleTalk on this interface? [no]: yes

     AppleTalk starting cable range [3]: 5

     AppleTalk ending cable range [4]: 5

     AppleTalk zone name [myzone]: ZZ Serial

     AppleTalk additional zone name: 

   Configure IPX on this interface? [no]: yes

     IPX network number [3]: B003

4.

The configuration you entered now displays and you are asked if 
you want to use the displayed configuration. If you enter no, you 
will lose the configuration information you just entered and you 
can begin the configuration again. If you type yes, the configura-
tion will be entered and saved in the startup configuration:

Use this configuration? [yes/no]: yes

Building configuration... 

Use the enabled mode 'configure' command to modify this configuration. 

Press RETURN to get started!

Summary of Contents for AISwitch AI2524



































































































































































































































































































































































































































Reviews:

No comments