manualshive.com logo in svg

Applied Innovation AISwitch AI2524, User Manual, Page: 377 / 418

Share
Download
Applied Innovation AISwitch AI2524 User Manual Download Page 377

Chapter 16: Basic Configuration

August 1997

Page 16-1

2524UM

Chapter 16: Basic Configuration

Connecting to the 
Network

Connecting to an Ethernet Network

The AI2524 can be connected to an Ethernet network by:

z

Using a straight-through 10BaseT cable to connect the 10BaseT 
port to a 10BaseT hub.

z

Using a crossover 10BaseT cable to connect the 10BaseT port to 
a PC network interface card.

Connecting to a WAN

z

If you have a 4-wire 56K/64K DSU/CSU module, use a straight-
through RJ-48S-to-RJ48S cable to connect the RJ-48S port to an 
RJ48S jack. 

z

If you have a FT1/T1 DSU/CSU module, use a straight-through 
RJ-48C-to-RJ48C cable to connect the RJ-48C port to an RJ48C 
jack. 

z

If you have a synchronous serial module, use a transition cable to 
connect the synchronous serial port to a modem or DSU/CSU.

Configuring

This chapter describes how to configure the AI2524 router and de-
scribes the following:

z

Booting the Router for the First Time

z

Configuring the Router

z

Specifying the Boot Method

z

Checking the Configuration Settings

This chapter provides just enough information to get the router up and 
running. Review the previous detailed configuration chapters for more 
information

Summary of Contents for AISwitch AI2524



































































































































































































































































































































































































































Reviews:

No comments