manualshive.com logo in svg

Applied Innovation AISwitch AI2524, User Manual, Page: 33 / 418

Share
Download
Applied Innovation AISwitch AI2524 User Manual Download Page 33

Chapter 3: Configuration Overview

August 1997

Page 3-3

2524UM

3.

After a few seconds you will see the user EXEC prompt 
(Router> . Enter the enable command to enter enable mode. You 
can only make configuration changes in enable mode.

Router> enable

The prompt changes to the privileged EXEC (enable) prompt:

Router#

4.

Enter the 

configure terminal

 command at the enable 

prompt to enter configuration mode:

Router# configure terminal

You can now enter any changes you want to the configuration. Refer 
to the appropriate sections of this manual for help with specific con-
figurations.

5.

Press <Ctrl-Z> to exit configuration mode.

Show 
Configuration

To see the current operating configuration, enter the 

show run-

ning-config

 command at the enable prompt:

Router# show running-config

To see the configuration in NVRAM, enter th

show startup-

config

 command at the enable prompt:

Router# show startup-config

The results of the 

show running-config

 and 

show startup-

config

 commands will be different if you have made changes to the 

configuration but have not yet written them to NVRAM.

Summary of Contents for AISwitch AI2524



































































































































































































































































































































































































































Reviews:

No comments