manualshive.com logo in svg

Applied Innovation AISwitch AI2524, User Manual, Page: 72 / 418

Share
Download
Applied Innovation AISwitch AI2524 User Manual Download Page 72

AI2524 Router Card User’s Manual

Page 5-6

August 1997

2524UM

Figure 5-1:Using SLARP to Acquire the New Router's IP 
Address

z

In response to BOOTP or RARP requests, an IP address is sent 
from the BOOTP or RARP server to newrouter.

A BOOTP or RARP server must have already been set up to map 
newrouter's MAC address to its IP address. If the BOOTP server 
does not reside on the directly attached network segment, routers 
between newrouter and the BOOTP server can be configured with 
the 

ip helper-address

 command to allow the request and 

response to be forwarded between segments, as shown in 

Figur

5-2

.

Summary of Contents for AISwitch AI2524



































































































































































































































































































































































































































Reviews:

No comments