manualshive.com logo in svg

Applied Innovation AISwitch AI2524, User Manual, Page: 273 / 418

Share
Download
Applied Innovation AISwitch AI2524 User Manual Download Page 273

Chapter 12: AI2524 X.25 Configuration Steps

August 1997

Page 12-15

2524UM

tination host defined for the protocol. Because only one destination is 
defined for the interface, the routing process need not consult the des-
tination address in the datagrams.

A multipoint subinterface is used to connect hosts for a given protocol. 
There is no restriction on the number of encapsulation commands that 
can be configured on a multipoint subinterface. Because the hosts ap-
pear on the same subinterface, they are not relying on the router to dis-
tribute routing updates between them. When a routing process 
forwards a datagram to a multipoint subinterface, the X.25 encapsula-
tion process must be able to map the datagram's destination address to 
a configured encapsulation command. If the routing process cannot 
find a map for the datagram destination address, the encapsulation will 
fail.

Note:

Because of the complex operations dependent on a sub-
interface and its type, the router will not allow a subinter-
face type to be changed, nor can a subinterface with the 
same number be re-established once it has been deleted. 
After a subinterface has been deleted, you must reload the 
Cisco IOS software (by using the 

reload

 command) to 

remove all internal references. However, you can easily 
reconstitute the deleted subinterface by using a different 
subinterface number.

Create and Configure X.25 Subinterfaces

In interface configuration mode, create and configure a subinterface 
by completing the first task and one or both of the second tasks:

1.

Create a point-to-point or multipoint subinterface. 

interface serial 

number.subinterface-number  

[point-to-point | multipoint]

2.

Configure an X.25 encapsulation map for the subinterface:  

x25 map 

protocol address  [protocol2 

address2 [... [protocol9 address9 ]]] x121-

address [option] 

And/or establish an encapsulation PVC for the subinterface:

x25 pvc 

circuit protocol address  [protocol2 

address2 [...[protocol9 address9 ]]] x121-
address [option]

Summary of Contents for AISwitch AI2524



































































































































































































































































































































































































































Reviews:

No comments