manualshive.com logo in svg

Applied Innovation AISwitch AI2524, User Manual, Page: 359 / 418

Share
Download
Applied Innovation AISwitch AI2524 User Manual Download Page 359

Chapter 13: AI2524 Frame Relay Configuration Steps

August 1997

Page 13-43

2524UM

Disable TCP/IP Header Compression

You can disable TCP/IP header compression by using either of two 
commands that have different effects, depending on whether Fram
Relay IP maps have been explicitly configured for TCP/IP header 
compression or have inherited their compression characteristics from 
the interface.

Frame Relay IP maps that have explicitly configured TCP/IP heade
compression must also have TCP/IP header compression explicitly 
disabled.

To disable TCP/IP header compression, perform one of these tasks in 
interface configuration mode:

z

Disable TCP/IP header compression on all Frame Relay IP maps 
that are not explicitly configured for TCP header compression.

no frame-relay ip tcp header-compression

frame-relay map ip 

ip-address dlci  

z

Disable TCP/IP header compression on a specified Frame Relay 
IP map.

nocompress tcp header-compression

Example: Disabling Inherited TCP/IP Header Compression

In this first example, the initial configuration is:

interface serial 1 

encapsulation frame-relay 

ip address 131.108.177.179 255.255.255.0 

frame-relay ip tcp header-compression passive

frame-relay map ip 131.108.177.177 177 broadcast 

frame-relay map ip 131.108.177.178 178 broadcast tcp header-compression

Enter these commands:

serial interface 1 

no frame-relay ip tcp header-compression

Summary of Contents for AISwitch AI2524



































































































































































































































































































































































































































Reviews:

No comments