manualshive.com logo in svg

Applied Innovation AISwitch AI2524, User Manual, Page: 168 / 418

Share
Download
Applied Innovation AISwitch AI2524 User Manual Download Page 168

AI2524 Router Card User’s Manual

Page 9-10

August 1997

2524UM

Configure ISO 
IGRP Dynamic 
Routing

The ISO IGRP is a dynamic distance-vector routing protocol designed 
by Cisco for routing an autonomous system that contains large, arbi-
trarily complex networks with diverse bandwidth and delay character-
istics.

To configure ISO IGRP, complete the tasks outlined in these sections. 
Only enabling ISO IGRP is required; the remaining task is optional, al-
though you might be required to perform it, depending upon your spe-
cific application:

z

Enable ISO IGRP

z

Configure ISO IGRP Parameters

In addition, you can also configure these miscellaneous features:

z

Filter routing information (refer to 

Create Packet-Forwarding Fil-

ters and Establish Adjacencies

)

z

Redistribute routing information from one routing process to an-
other (refer to 

Redistribute Routing Information

)

z

Configure administrative distances (refer to 

Specify Preferred 

Routes

)

Enable ISO IGRP

To configure ISO IGRP dynamic routing, you must enable the ISO 
IGRP routing process, identify the address for the router, and specify 
the interfaces that are to route ISO IGRP. Optionally, you can set a 
level for your routing updates when you configure the interfaces. 
CLNS routing is enabled by default on routers when you configure 
ISO IGRP. You can specify up to ten ISO IGRP routing processes.

In global configuration mode, configure ISO IGRP dynamic routing 
on the router:

1.

Enable the ISO IGRP routing process and enter router configura-
tion mode.

router iso-igrp  [

tag]

2.

Configure the NET or address for the routing process. 

net 

network-entity-title

Although IS-IS allows you to configure multiple NETs, ISO IGRP al-
lows only one NET per routing process.

Summary of Contents for AISwitch AI2524



































































































































































































































































































































































































































Reviews:

No comments