manualshive.com logo in svg

Applied Innovation AISwitch AI2524, User Manual, Page: 147 / 418

Share
Download
Applied Innovation AISwitch AI2524 User Manual Download Page 147

Chapter 8: AI2524 Protocol Configuration Steps

August 1997

Page 8-9

2524UM

Configure Route Calculation Timers

You can configure the delay time between when OSPF receives a to-
pology change and when it starts a Shortest Path First (SPF) calcula-
tion. You can also configure the hold time between two consecutive 
SPF calculations. Type this command in router configuration mode:

timers spf 

spf-delay spf-holdtime  

Configure OSPF over On-Demand Circuits

The OSPF on-demand circuit is an enhancement to the OSPF protocol 
that allows efficient operation over on-demand circuits like ISDN, 
X.25 SVCs, and dial-up lines. This feature supports RFC 1793, ex-
tending OSPF to Support Demand Circuits. 

With this feature, periodic hellos are suppressed and the periodic re-
freshes of LSAs are not flooded over the demand circuit. 

To configure OSPF for on-demand circuits, perform these tasks: 

1.

Enable OSPF operation. 

router ospf 

process-id

2.

Configure OSPF on an on-demand circuit.

ip ospf demand-circuit 

If the router is part of a point-to-point topology, then only one end of 
the demand circuit must be configured with this command. However, 
all routers must have this feature loaded. 

If the router is part of a point-to-multipoint topology, only the multi-
point end must be configured with this command. 

Implementation Considerations

Because LSAs that include topology changes are flooded over an on-
demand circuit, it is advised to put demand circuits within OSPF. 

Summary of Contents for AISwitch AI2524



































































































































































































































































































































































































































Reviews:

No comments