manualshive.com logo in svg

Applied Innovation AISwitch AI2524, User Manual, Page: 139 / 418

Share
Download
Applied Innovation AISwitch AI2524 User Manual Download Page 139

Chapter 8: AI2524 Protocol Configuration Steps

August 1997

Page 8-1

2524UM

Chapter 8: AI2524 Protocol Configuration 

Steps

Introduction

This chapter describes the AI2524 protocol configuration steps for th
OSPF TCP/IP, IGRP TCP/IP and RIP TCP/IP.

AI2524 OSPF 
TCP/IP 
Configuration 
Steps

Open Shortest Path First (OSPF) is an IGP designed expressly for IP 
networks. OSPF supports IP subnetting and tagging of externally de-
rived routing information. OSPF also allows packet authentication and 
uses IP multicast when sending/receiving packets. 

OSPF typically requires coordination among many internal routers, 
area border routers (routers connected to multiple areas), and autono-
mous system boundary routers. At a minimum, OSPF-based routers or 
access servers can be configured with all default parameter values, no 
authentication, and interfaces assigned to areas. If you plan to custom-
ize your environment, ensure coordinated configurations of all routers.

To configure OSPF, complete these tasks. You must enable OSPF; the 
other tasks are optional, but might be required for your application. 

z

Enable OSPF

 

z

Configure OSPF Interface Parameters

 

z

Configure OSPF over Different Physical Networks

z

Configure OSPF Area Parameters

 

z

Configure OSPF Not So Stubby Area (NSSA

 

z

Configure Route Summarization between OSPF Areas

z

Configure Route Summarization When Redistributing Routes into 
OSPF

 

z

Create Virtual Links

 

z

Generate a Default Route

z

Configure Lookup of DNS Names

 

z

Force the Router ID Choice with a Loopback Interfac

z

Disable Default OSPF Metric Calculation Based on Bandwidth

 

z

Configure OSPF on Simplex Ethernet Interfaces

 

Summary of Contents for AISwitch AI2524



































































































































































































































































































































































































































Reviews:

No comments