manualshive.com logo in svg

Applied Innovation AISwitch AI2524, User Manual, Page: 164 / 418

Share
Download
Applied Innovation AISwitch AI2524 User Manual Download Page 164

AI2524 Router Card User’s Manual

Page 9-6

August 1997

2524UM

Addressing Examples

Examples of OSI network and GOSIP NSAP addresses using the ISO 
IGRP implementation are described in the next sections.

The OSI network NSAP address format is illustrated as:

|     Domain|Area|     System ID| S| 47.0004.004D.0003.0000.0C00.62E6.00

This is an example of the GOSIP NSAP address structure. This struc-
ture is mandatory for addresses allocated from the International Code 
Designator (ICD) 0005 addressing domain. Refer to the GOSIP docu-
ment, U.S. Government Open Systems Interconnection Profile (GO-
SIP), Draft Version 2.0, April 1989, for more information.

|                    Domain|     Area|System ID| S| 

47.0005.80.ffff00.0000.ffff.0004.0000.0c00.62e6.00

 |   |    |    |    |    

AFI IDI  DFI  AAI Resv  RD

Routing Table Example

You enter static routes by specifying NSAP prefix and next-hop NET 
pairs (by using the 

clns route

 command). The NSAP prefix can 

be any portion of the NSAP address. NETs are similar in function to 
NSAP addresses.

If an incoming packet has a destination NSAP address that does not 
match any existing NSAP addresses in the routing table, the Cisco IOS 
software will try to match the NSAP address with an NSAP prefix to 
route the packet. In the routing table, the best match means the longest 
NSAP prefix entry that matches the beginning of the destination 
NSAP address.

Summary of Contents for AISwitch AI2524



































































































































































































































































































































































































































Reviews:

No comments