Applied Innovation AISwitch AI2524 User Manual Download Page 198

Page: 198 / 418

AI2524 Router Card User’s Manual

Page 9-40

August 1997

2524UM

Pass ISO CLNS traffic to end systems without routing:

interface serial 1

clns enable

Configure a static route to Router B:

clns route 39.0001 bar

Router B

This configuration shows how to configure Router B for static
interdomainrouting:

router iso-igrp pleiades

Configure the network entity title for the routing process:

net 47.0007.0200.0200.1112.1314.1516.00

Define the name sid to be used in place of Router A's NSAP:

clns host sid 47.0006.0200.0100.0001.0102.0304.0506.00

Specify iso-igrp routing using the specified tag pleiades:

interface ethernet 0

clns router iso-igrp pleiades

Pass ISO CLNS traffic to end systems without routing:

interface serial 0 clns enable

Summary of Contents for AISwitch AI2524



































































































































































































































































































































































































































Search results

Summary of Contents for AISwitch AI2524

Reviews:

Applied Innovation AISwitch AI2524, User Manual, Page: 198 / 418

Search results

Summary of Contents for AISwitch AI2524

Reviews: