manualshive.com logo in svg

Applied Innovation AISwitch AI2524, User Manual, Page: 181 / 418

Share
Download
Applied Innovation AISwitch AI2524 User Manual Download Page 181

Chapter 9: AI2524 OSI/CLNP Configuration Steps

August 1997

Page 9-23

2524UM

tag of remote-domain. Most comment lines have been eliminated from 
this example to avoid redundancy.

router isis 

net 39.0001.0001.0000.0c00.1111.00

 

1.

Redistribute iso-igrp routing information throughout remote-do-
main:

redistribute iso-igrp remote-domai n

!

router iso-igrp remote-domain

net 39.0002.0001.0000.0c00.1111.00

 

2.

Redistribute IS-IS routing information:

redistribute isis 

! 

interface ethernet 0 

clns router isis 

! 

interface serial 0 

clns router iso-igrp remote

Assign Multiple Area Addresses to IS-IS Areas

IS-IS routing supports the assignment of multiple area addresses on 
the same router. This concept is referred to as multihoming. Multi-
homing provides a mechanism for smoothly migrating network ad-
dresses as:

z

Splitting up an area. Nodes within a given area can accumulate to 
a point that they are difficult to manage, cause excessive traffic, or 
threaten to exceed the usable address space for an area. Multiple 
area addresses can be assigned so that you can smoothly partition 
a network into separate areas without disrupting service.

z

Merging areas. Use transitional area addresses to merge as many 
as three separate areas into a single area that share a common area 
address.

z

Transition to a different address. You may need to change an are
address for a particular group of nodes. Use multiple area address-
es to allow incoming traffic intended for an old area address to 
continue being routed to associated nodes.

Summary of Contents for AISwitch AI2524



































































































































































































































































































































































































































Reviews:

No comments