manualshive.com logo in svg

Applied Innovation AISwitch AI2524, User Manual, Page: 14 / 418

Share
Download
Applied Innovation AISwitch AI2524 User Manual Download Page 14

AI2524 Router Card User’s Manual

TOC-10

August 1997

2524UM

Chapter 15: 56/64-kbps Switched and Digital Data Services (DDS) Interface Config-
uration Steps...............................................................................................................15-1

Introduction .................................................................................................................15-1
Set the Clock Source ...................................................................................................15-1
Set the Network Line Speed........................................................................................15-2
Enable Scrambled Data Coding ..................................................................................15-3
Change between DDS and Switched Dial-Up Modes ................................................ 15-3
Enable Acceptance of a Remote Loopback Request .................................................. 15-4
Select a Service Provider ............................................................................................15-4

Chapter 16: Basic Configuration..............................................................................16-1

Connecting to the Network .........................................................................................16-1

Connecting to an Ethernet Network...............................................................16-1
Connecting to a WAN ....................................................................................16-1

Configuring .................................................................................................................16-1

Booting the Router for the First Time............................................................16-2

Configuring the Router ...............................................................................................16-2

Using Configuration Mod ............................................................................16-3
Using AutoInstall ...........................................................................................16-4
Using the System Configuration Dialog ........................................................16-5

Configuring the Ethernet or Token Ring Interfaces.................................................... 16-10
Configuring the Synchronous Serial Interfaces ..........................................................16-11
Configuring ISDN .......................................................................................................16-12
Configuring Switched 56 ............................................................................................16-14
Configuring DDS ........................................................................................................16-16
Configuring the Fractional T1/T1 DSU/CSU WAN Module ..................................... 16-17
Specifying the Boot Method .......................................................................................16-18
Checking the Configuration Settings ..........................................................................16-20

Chapter 17: Command References ..........................................................................17-1

Introduction .................................................................................................................17-1

Chapter 18: System Error Messages........................................................................18-1

Introduction .................................................................................................................18-1

Chapter 19: Debug Command Reference................................................................19-1

Introduction .................................................................................................................19-1

Appendix A: Release Notes ........................................................................................A-1

New Features................................................................................................................ A-1
ISDN/BRI Inferface..................................................................................................... A-2
Configuring ISDN ........................................................................................................ A-3

Appendix B: Acronyms .............................................................................................. B-1

Summary of Contents for AISwitch AI2524



































































































































































































































































































































































































































Reviews:

No comments