manualshive.com logo in svg

Applied Innovation AISwitch AI2524, User Manual, Page: 101 / 418

Share
Download
Applied Innovation AISwitch AI2524 User Manual Download Page 101

Chapter 7: Manually Loading System Images

August 1997

Page 7-1

2524UM

Chapter 7: Manually Loading System 

Images

Introduction

This chapter outlines the steps to load and maintain system images, 
microcode images, and configuration files. These instructions describe 
copying system images from routers to network servers (and vice 
versa), displaying and comparing different configuration files, and 
listing the Cisco IOS software version running on the router.

This chapter also explains how to manually load system images from 
ROM monitor so you can successfully boot the router when typical 
startup processes malfunction.

z

System images contain the system software.

z

Microcode images contain microcode to be downloaded to various 
hardware devices.

z

Configuration files contain commands entered to customize th
function of the Cisco IOS software.

To benefit most from these instructions, your router must contain 
minimal configuration that allows you to interact with the system soft-
ware. You can create a basic configuration file using the setup com
mand facility. See the user guide for your hardware platform for more 
information on using setup at first-time startup. Refer to 

Use Setup 

after First-Time Startup

, for more information.

Summary of Contents for AISwitch AI2524



































































































































































































































































































































































































































Reviews:

No comments