manualshive.com logo in svg

Applied Innovation AISwitch AI2524, User Manual, Page: 303 / 418

Share
Download
Applied Innovation AISwitch AI2524 User Manual Download Page 303

Chapter 12: AI2524 X.25 Configuration Steps

August 1997

Page 12-45

2524UM

This configuration specifies that traffic from any other interface on 
Cisco Router C4 that is intended for any NSAP address with NSAP-
prefix 38.8261.20 will be switched through Serial 0.

interface serial 0 

encapsulation x25 

x25 address 00002 

x25 map cmns 38.8261.20

Configuration for Router C3

This configuration specifies that any traffic from any other interface 
intended for any NSAP address with NSAP 38.8261.20 will be 
switched to MAC address 0800.4e02.123f through Ethernet 0.

interface ethernet 0 

cmns enable 

x25 map cmns 38.8261.20 0800.4e02.123f

This configuration specifies that traffic from any other interface on  
Router C3 that is intended for any NSAP address with NSAP-prefix 
38.8261.21 will be switched through Serial 1.

interface serial 1 

encapsulation x25 

x25 address 00001 

x25 map cmns 38.8261.21

Create X.29 
Access Lists

Protocol translation software supports access lists, which make it pos-
sible to limit access to the access server from X.25 hosts. Access lists 
take advantage of the message field defined by Recommendation 
X.29, which describes procedures for exchanging data between two 
PADs or between a PAD and a DTE device.

To define X.29 access lists, perform these tasks:

z

Create an Access List

z

Apply an Access List to a Line

When configuring protocol translation, you can specify an access list 
number with each 

translate

 command. When translation sessions 

result from incoming PAD connections, the corresponding X.29 ac
cess list is used.

Summary of Contents for AISwitch AI2524



































































































































































































































































































































































































































Reviews:

No comments