manualshive.com logo in svg

Applied Innovation AISwitch AI2524, User Manual, Page: 246 / 418

Share
Download
Applied Innovation AISwitch AI2524 User Manual Download Page 246

AI2524 Router Card User’s Manual

Page 11-20

August 1997

2524UM

using V.34 modems. However, packets might be dropped occasionally 
if the MTU is small or if large bursts of short frames occur.

Beginning in global configuration mode, configure a dialer interface 
to support PPP encapsulation and Multilink PPP:

1.

Define a dialer rotary group. 

interface dialer 

number

2.

Specify no IP address for the interface.

no ip address

3.

Enable PPP encapsulation.

encapsulation ppp

4.

Enable DDR on the interface. 

dialer in-band 

5.

Configure bandwidth on demand by specifying the maximum load 
before the dialer places another call to a destination. 

dialer load-threshold 

load [inbound | 

outbound | either] 

6.

Enable Multilink PPP. 

ppp multilink

Configure Multilink PPP on a Single ISDN BRI Interface

To enable Multilink PPP on a single Integrated Services Digital Net
work (ISDN) BRI interface, you are not required to define a dialer ro-
tary group separately because ISDN interfaces are dialer rotary groups 
by default.

Beginning in global configuration mode, enable PPP on an ISDN BRI 
interface:

1.

Specify an interface. 

interface bri 

number

2.

Provide an appropriate protocol address for the interface. 

ip address 

ip-address mask

3.

Enable PPP encapsulation. 

encapsulation ppp 

Summary of Contents for AISwitch AI2524



































































































































































































































































































































































































































Reviews:

No comments