manualshive.com logo in svg

Applied Innovation AISwitch AI2524, User Manual, Page: 157 / 418

Share
Download
Applied Innovation AISwitch AI2524 User Manual Download Page 157

Chapter 8: AI2524 Protocol Configuration Steps

August 1997

Page 8-19

2524UM

Run IGRP and RIP Concurrently

It is possible to run IGRP and RIP concurrently. The IGRP informa-
tion will override the RIP information by default because of IGRP's 
administrative distance.

Running IGRP and RIP concurrently does not work well when the net-
work topology changes. Because IGRP and RIP have different update 
timers, and because they require different amounts of time to propa-
gate routing updates, one part of the network will follow IGRP routes 
and another part will follow RIP routes. This results in routing loops. 
Although these loops do not exist for long, the Time To Live (TTL) 
will quickly reach zero, and ICMP will send a TTL exceeded message. 
This message will cause most applications to stop attempting network 
connections.

Disable the Validation of Source IP Addresses

By default, the software validates the source IP address of incoming 
RIP routing updates. If that source address is not valid, the software 
discards the routing update.

Consider disabling this feature if you have a router that is off network 
and you want to receive its updates. Disabling this feature is not rec
ommended under normal circumstances. To disable the default func
tion that validates the source IP addresses of incoming routing updates, 
perform this task in router configuration mode:

z

Disable the validation of the source IP address of incoming RIP 
routing updates. 

no validate-update-source ion

In addition to running multiple routing protocols simultaneously, the 
Cisco IOS software can redistribute information from one routing pro-
tocol to another. For example, you can instruct the software to readver-
tise IP Enhanced IGRP-derived routes using the RIP protocol or to 
readvertise static routes using the IP Enhanced IGRP protocol. This 
capability applies to all the IP-based routing protocols.

You may also conditionally control the redistribution of routes be
tween routing domains by defining a method known as route maps be-
tween the two domains.

z

To redistribute routes from one protocol into another, type this 
command in router configuration mode:

redistribute protocol 

autonomous-system-

number [route-map  map-tag]

Summary of Contents for AISwitch AI2524



































































































































































































































































































































































































































Reviews:

No comments