manualshive.com logo in svg

Applied Innovation AISwitch AI2524, User Manual, Page: 334 / 418

Share
Download
Applied Innovation AISwitch AI2524 User Manual Download Page 334

AI2524 Router Card User’s Manual

Page 13-18

August 1997

2524UM

Customize Frame 
Relay for Your 
Network

Perform these tasks to customize Frame Relay:

z

Configure Frame Relay Subinterfaces

z

Configure Frame Relay Switching

z

Disable or Reenable Frame Relay Inverse ARP

z

Create a Broadcast Queue for an Interface

z

Configure Payload Compression

z

Configure TCP/IP Header Compression

z

Configure Discard Eligibility

z

Configure DLCI Priority Levels

Configure Frame Relay Subinterfaces

To understand and define Frame Relay Subinterfaces, perform these 
tasks:

z

Understand Frame Relay Subinterfaces

z

Define Frame Relay Subinterfaces

z

Define Subinterface Addressing

After these tasks are completed, you can also perform these optional 
tasks:

z

Configure Transparent Bridging for Frame Relay

z

Configure a Backup Interface for a Subinterface

Understand Frame Relay Subinterfaces

Frame Relay subinterfaces provide a mechanism for supporting par-
tially meshed Frame Relay networks. Most protocols assume transitiv-
ity on a logical network; that is, if station A can talk to station B, and 
station B can talk to station C, then station A should be able to talk to 
station C directly. Transitivity is true on LANs, but not on Fram
Relay networks unless A is directly connected to C.

Additionally, certain protocols such as transparent bridging cannot b
supported on partially meshed networks because they require "split 
horizon," in which a packet received on an interface cannot be trans
mitted out the same interface even if the packet is received and trans
mitted on different virtual circuits.

Summary of Contents for AISwitch AI2524



































































































































































































































































































































































































































Reviews:

No comments