Home
/
Applied Innovation
/
AISwitch AI2524
/
User Manual

Applied Innovation AISwitch AI2524, User Manual, Page: 154 / 418

Share

Page: 154 / 418

Applied Innovation AISwitch AI2524 User Manual Download Page 154

AI2524 Router Card User’s Manual

Page 8-16

August 1997

2524UM

AI2524 RIP TCP/
IP Configuration

Routing Information Protocol (RIP) uses broadcast User Datagram
Protocol (UDP) data packets to exchange routing information.

The Cisco IOS software sends routing information updates (advertise-
ments) every 30 seconds. If a router does not receive an update from
another router for 180 seconds or more, it marks the routes served by
the nonupdating router as being unusable. If there is still no update
after 240 seconds, the router removes all routing table entries for the
nonupdating router.

RIP sends updates to the interfaces in the specified networks. If an in-
terface's network is not specified, it will not be advertised in any RIP
update.

RIP Configuration Task List

To configure RIP, complete the tasks outlined in the nest sections. You
must enable RIP. The remaining tasks are optional.

z

Enable RIP

z

Allow Point-to-Point Updates for RI

z

Specify a RIP Version

z

Enable RIP Authentication

z

Disable Route Summarization

z

Run IGRP and RIP Concurrently

z

Disable the Validation of Source IP Addresses

Enable RIP

To enable RIP, perform these tasks, starting in global configuration
mode:

1.

Enable a RIP routing process, which places you in router configu-
ration mode.

router rip

2.

Associate a network with a RIP routing process.

network

network-number

Allow Point-to-Point Updates for RIP

RIP is normally a broadcast protocol. Therefore, for RIP routing up-
dates to reach point-to-point or nonbroadcast networks, you must con-
figure the Cisco IOS software to permit this exchange of routing

«
...
152
153
154
155
156
...
»

Summary of Contents for AISwitch AI2524



































































































































































































































































































































































































































Reviews:

No comments