manualshive.com logo in svg

Applied Innovation AISwitch AI2524, User Manual, Page: 255 / 418

Share
Download
Applied Innovation AISwitch AI2524 User Manual Download Page 255

Chapter 11: AI2524 Sync PPP Configuration Steps

August 1997

Page 11-29

2524UM

Configure Incoming VPDN Connections on the Home 
Gateway

In global configuration mode, configure virtual private dialup net-
working on a home gateway router or access server:

1.

Enable virtual private networking. 

vpdn enable

2.

Specify the remote host, the local name to use for authenticating, 
and the virtual template to use. 

vpdn incoming 

remote-name local-name  

virtual-template 

number

Configure Outgoing VPDN Connections on the Network 
Access Server

In global configuration mode, configure a network access server to 
make outgoing L2F connections to a home gateway for VPDN:

1.

Enable virtual private networking. 

vpdn enable

2.

Specify the remote host that is to accept L2F connections. 

vpdn outgoing 

domain-name local-name  ip ip-

address

Example: Network Access Server Servicing Multiple 
Domains

This example provides VDPN configurations for a single NAS and 
two different gateways. The two gateways are presumably located at 
two entirely separate companies. The NAS decides which company to 
forward to based on the domain name that is passed by the user.

The commands also illustrate where  to configure the commands 

vpdn 

outgoing

 (on the network access server) and 

vpdn incoming 

(on a home gateway).

NAS1

vpdn enable 

vpdn outgoing domain1.com nas1 ip 1.1.1.1 

vpdn outgoing domain2.com nas2 ip 2.2.2.2

Summary of Contents for AISwitch AI2524



































































































































































































































































































































































































































Reviews:

No comments