manualshive.com logo in svg

Applied Innovation AISwitch AI2524, User Manual, Page: 248 / 418

Share
Download
Applied Innovation AISwitch AI2524 User Manual Download Page 248

AI2524 Router Card User’s Manual

Page 11-22

August 1997

2524UM

Example: Multilink PPP on One ISDN Interface

This example enables Multilink PPP on the BRI 0 interface. Because 
an ISDN interface is a rotary group by default, when one BRI is con-
figured, no dialer rotary group configuration is required.

interface bri 0 

description connected to ntt 81012345678902 

ip address 7.1.1.7 255.255.255.0 

encapsulation ppp 

dialer idle-timeout 30 

dialer load-threshold 40 either 

dialer map ip 7.1.1.8 name atlanta 81012345678901 

dialer-group 1 

ppp authentication pap 

ppp multilink

Configure Multilink PPP on Multiple ISDN BRI Interfaces

To enable Multilink PPP on multiple ISDN BRI interfaces, set up a di-
aler rotary interface and configure it for Multilink PPP and then con
figure the BRIs separately and add them each to the same rotary group.

Beginning in global configuration mode, set up the dialer rotary inter-
face for the BRI interfaces:

1.

Specify the dialer rotary interface. 

interface dialer 

number

2.

Specify the protocol address for the dialer rotary interface. 

ip address 

address mask

3.

Enable PPP encapsulation.

encapsulation ppp

4.

Specify in-band dialing.

dialer in-band

5.

Specify the dialer idle timeout period, using the same timeout pe-
riod as the individual BRI interfaces. 

dialer idle-timeout 

seconds 

Summary of Contents for AISwitch AI2524



































































































































































































































































































































































































































Reviews:

No comments