Applied Innovation AISwitch AI2524 User Manual Download Page 250

Page: 250 / 418

AI2524 Router Card User’s Manual

Page 11-24

August 1997

2524UM

Specify the dialer load threshold for bringing up additional WAN
links.

dialer load-threshold

load

Repeat Steps 1 through 6 for each BRI you want to belong to the same
dialer rotary group.

When Multilink PPP is configured and you want a multilink bundle to
be connected indefinitely, use the

dialer idle-timeout

com-

mand to set a very high idle timer.

The

dialer load-threshold 1

command does not keep a mul-

tilink bundle of n links connected indefinitely, and the

dialer

load-threshold 2

command does not keep a multilink bundle of

two links connected indefinitely.

Summary of Contents for AISwitch AI2524



































































































































































































































































































































































































































Search results

Summary of Contents for AISwitch AI2524

Reviews:

Applied Innovation AISwitch AI2524, User Manual, Page: 250 / 418

Search results

Summary of Contents for AISwitch AI2524

Reviews: