manualshive.com logo in svg

Applied Innovation AISwitch AI2524, User Manual, Page: 185 / 418

Share
Download
Applied Innovation AISwitch AI2524 User Manual Download Page 185

Chapter 9: AI2524 OSI/CLNP Configuration Steps

August 1997

Page 9-27

2524UM

IS-IS

To run IS-IS instead of ISO IGRP, use this configuration. The illustra-
tion in 

Figure 9-

 still applies. Ethernet interface 2 is configured for 

IS-IS routing and is assigned the tag of test-proc2.

router iso-igrp test-proc1 

net 49.0002.0002.bbbb.bbbb.bbbb.00 

router isis test-proc2 

net 49.0001.0002.aaaa.aaaa.aaaa.00 

! 

interface ethernet 1 

clns router iso-igrp test-proc1 

! 

interface serial 2 

clns router iso-igrp test-proc1 

! 

interface ethernet 2 

clns router IS-IS test-proc2

To allow CLNS packets only to blindly pass through an interface with-
out routing updates, you could use a simple configuration. This exam-
ple shows such a configuration:

clns routing 

interface serial 2 

This permits serial 2 to pass CLNS packets without having CLNS rout-
ing turned on:

clns enable

Configure IS-IS Parameters

Cisco's IS-IS implementation allows you to customize certain IS-IS 
parameters. You can perform the optional tasks:

z

Specify Router-Level S upport

z

Configure IS-IS Authentication Passwords

z

Ignore IS-IS Link-State Packet (LSP) Errors

z

Log Adjacency State Changes

z

Change IS-IS LSP MTU Size

Summary of Contents for AISwitch AI2524



































































































































































































































































































































































































































Reviews:

No comments