manualshive.com logo in svg

Applied Innovation AISwitch AI2524, User Manual, Page: 15 / 418

Share
Download
Applied Innovation AISwitch AI2524 User Manual Download Page 15

Chapter 1: Introduction

August 1997

Page 1-1

2524UM

Chapter 1: Introduction

Documentation 
Overview

This manual documents the use and operation of the AI2524 in an 
AISwitch system. These topics are covered:

Chapter 1

Introduction

This chapter provides a documentation over-
view, related documentation, contact infor
mation, and text conventions.

Chapter 2

AI2524 Overview

This chapter describes the Cisco IOS soft-
ware features and AI2524 hardware specifi-
cations.

Chapter 3

Configuration Overview

This chapter describes the process of booting 
the router for the first time and provides over-
views of configuration methods.

Chapter 4

Understanding the User Interfac

This chapter introduces Cisco IOS softwar
interface, and includes instructions for ac-
cessing command modes, context-sensitiv
help, and command history and editing fea-
tures.

Chapter 5

Using AutoInstall

This chapter describes how use AutoInstall 
for automatic and dynamic configuration o
the AI2524. 

Chapter 6

Using the System Configuration Dialog

This chapter describes how to use the System 
Configuration Dialog to manually configure 
the router.

Chapter 7

Manually Loading System Images

This chapter describes how to manually load 
system images in the event that typical start-
up procedures malfunction.

Summary of Contents for AISwitch AI2524



































































































































































































































































































































































































































Reviews:

No comments