manualshive.com logo in svg

Analog Devices ADSP-21261 SHARC, Hardware Reference Manual

The Analog Devices ADSP-21261 SHARC is a powerful digital signal processor designed specifically for audio applications. Enhance your understanding of this innovative product by accessing its comprehensive Hardware Reference Manual. This invaluable manual can be downloaded for free from manualshive.com, providing you with essential insights and technical guidance.

Share
Download
background image

8-8

ADSP-2126x SHARC Processor Hardware Reference

 

Table 8-2

 does not show 

ALE

 cycles; it shows only the order of the 

data reads and writes.

Parallel port DMAs can only be performed to 32-bit (normal word) 
internal memory.

Transfer Protocol

The external interface follows the standard asynchronous SRAM access 
protocol. The programmable Data Cycle Duration (

PPDUR

) and optional 

Bus Hold Cycle (

BHC

) addition at the end of each data cycle are provided 

to interface with memories having different access time requirements. The 
data cycle duration is programmed via the 

PPDUR

 bit in the 

PPCTL

 register. 

The hold cycle at the end of the data cycle is programmed via the 

PPBHC

 

bit in the 

PPCTL

 register.

Disabling the parallel port (

PPEN

 bit is cleared) flushes both parallel 

port FIFOs, 

RXPP

, and 

TXPP

.

For standard asynchronous SRAM there are two transfer modes—8-bit 
and 16-bit mode. In 8-bit mode, the address range is 0x0 to 0xFFFFFF 
which is 16M bytes (4M 32-bit words). In 16-bit mode, the address range 
is 0x0 to 0xFFFF which is a 128K bytes (32K 32-bit words). Although 
programs can initiate reads or writes on one and two byte boundaries, the 
parallel port always transfers 4 bytes (two 16-bit or four 8-bit words).

Table 8-2. Unpacking Sequence for 32-Bit Data

Transfer

AD7–0, 32-bit to 8-bit 
(8-bit bus, LSW first)

AD15–0, 32-bit to 16-bit 
(16-bit bus, LSW first)

First

Word 1; bits 7–0 

Word 1; bits 15–0

Second

Word 1; bits 15–8

Word 1; bits 31–16 

Third

Word 1; bits 23–16

Fourth

Word 1; bits 31–24

Summary of Contents for ADSP-21261 SHARC















































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for ADSP-21261 SHARC

Udoo NEO Step-By-Step Manual preview
NEO
Brand: Udoo Pages: 7
Palo Alto Network M-200 Reference Manual preview
M-200
Brand: Palo Alto Network Pages: 56
X-Micro XWL-11GPRG Quick Start Manual preview
XWL-11GPRG
Brand: X-Micro Pages: 9
X-Micro XWL-11GPAG Quick Installation Manual preview
XWL-11GPAG
Brand: X-Micro Pages: 19
EK-Quantum Kinetic FLT 80 D5/DDC Body User Manual preview
Kinetic FLT 80 D5/DDC Body
Brand: EK-Quantum Pages: 16
Internet Security Systems Proventia A1204 User Manual preview
Proventia A1204
Brand: Internet Security Systems Pages: 42
LGC wireless InterReach Fusion SingleStar Installation And Operation Manual preview
InterReach Fusion SingleStar
Brand: LGC wireless Pages: 154
Variscite VAR-EXT-CB105 Datasheet preview
VAR-EXT-CB105
Brand: Variscite Pages: 18
RANA Systems Elite Controller User Manual preview
Elite Controller
Brand: RANA Systems Pages: 328
Comelit IPNVR004BPOE Manual preview
IPNVR004BPOE
Brand: Comelit Pages: 19
DigiTech RPX400 Troubleshooting Manual preview
RPX400
Brand: DigiTech Pages: 6
AC Infinity AIRCOM Series User Manual preview
AIRCOM Series
Brand: AC Infinity Pages: 24
Uctronics U6180 Instruction Manual preview
U6180
Brand: Uctronics Pages: 2
Ciara Horizon D10750 Disassembly Manual preview
Horizon D10750
Brand: Ciara Pages: 14
QSC Q-SYS QIO-GP8x8 Hardware User Manual preview
Q-SYS QIO-GP8x8
Brand: QSC Pages: 13
Atmel SAMA5D31-EK User Manual preview
SAMA5D31-EK
Brand: Atmel Pages: 123
JETWAY 939GT2-Ultra Series User Manual preview
939GT2-Ultra Series
Brand: JETWAY Pages: 55
Fujitsu 467 Manual preview
467
Brand: Fujitsu Pages: 36

Brands by name

Popular brands

Load more brands