manualshive.com logo in svg

Analog Devices ADSP-21261 SHARC, Hardware Reference Manual

The Analog Devices ADSP-21261 SHARC is a powerful digital signal processor designed specifically for audio applications. Enhance your understanding of this innovative product by accessing its comprehensive Hardware Reference Manual. This invaluable manual can be downloaded for free from manualshive.com, providing you with essential insights and technical guidance.

Share
Download
background image

I/O Processor Registers

A-78

ADSP-2126x SHARC Processor Hardware Reference

 

22

FS_BOTH

FS Both Enable.

 This bit issues WS if data is present in 

both

 trans-

mit buffers, if set (= 1). If cleared (= 0), WS is issued if data is pres-
ent in either transmit buffer. This bit is reserved when the SPORT is 

in multichannel, I

2

S and Left-justified Sample Pair mode.

23

BHD

Buffer Hang Disable.

 This bit ignores a core hang, when set (= 1). 

When cleared (= 0), this bit indicates a core stall. The core stall 
occurs when the transmit buffer is full or the receive buffer is empty 
and the core tries to write or read from the FIFO respectively. This 
bit applies to all modes

24

SPEN_B

Enable Channel B Serial Port.

 Enables if set, (= 1) or disables if 

cleared, (= 0) the corresponding serial port B channel.
This bit is reserved when the SPORT is in Multichannel mode.

25

SPTRAN

Data Direction Control.

 Enables receive buffers if cleared (= 0), or 

activates transmit buffers if set (= 1). This bit is reserved when the 
SPORT is in Multichannel mode.

26

ROVF_B, 
TUVF_B

Channel B Error Status (sticky, read-only).

 Indicates if the serial 

transmit operation has underflowed or a receive operation has over-
flowed in the channel B data buffer. This bit is reserved when the 
SPORT is in Multichannel mode.

28–27

DXS_B

Channel B Data Buffer Status (read-only).

 Indicates the status of 

the serial port’s channel B data buffer as follows: 11 = full, 00 = 
empty, 10 = partially full. This bit is reserved when the SPORT is in 
Multichannel mode.

29

ROVF_A or 
TUVF_A

Channel A Error Status (sticky, read-only).

 Indicates if the serial 

transmit operation has underflowed or a receive operation has over-
flowed in the channel A data buffer.

31–30

RXS_A or 
TXS_A

Channel A Data Buffer Status (read-only).

 Indicates the status of 

the serial port’s channel A data buffer as follows: 11 = full, 00 = 
empty, 
10 = partially full.

Table A-23. SPCTLx Register Bit Descriptions  (Cont’d)

Bits

Name

Definition

Summary of Contents for ADSP-21261 SHARC















































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for ADSP-21261 SHARC

IBM 3270 Operation Manual preview
3270
Brand: IBM Pages: 86
Stanwax Laser S4i Manual preview
S4i
Brand: Stanwax Laser Pages: 9
Paradyne Fan Tray 8820-S2-900 Installation Instructions Manual preview
Fan Tray 8820-S2-900
Brand: Paradyne Pages: 6
Xmart SNMP06 Reference Manual preview
SNMP06
Brand: Xmart Pages: 8
Compro Technology RS-2104 Quick Installation Manual preview
RS-2104
Brand: Compro Technology Pages: 2
Ubiquiti UniFi WiFi BaseStation XG Quick Start Manual preview
UniFi WiFi BaseStation XG
Brand: Ubiquiti Pages: 19
CG Emotron OSTO 100 Instruction Manual preview
Emotron OSTO 100
Brand: CG Pages: 112
ZALMAN Fatal1ty FS-V7 User Manual preview
Fatal1ty FS-V7
Brand: ZALMAN Pages: 9
Acromag APCe7012E-LF User Manual preview
APCe7012E-LF
Brand: Acromag Pages: 23
Top RAMS1000 User Manual preview
RAMS1000
Brand: Top Pages: 21
Advantech PPC-3211W User Manual preview
PPC-3211W
Brand: Advantech Pages: 66
ICP DAS USA I-87K Series User Manual preview
I-87K Series
Brand: ICP DAS USA Pages: 31
GSA Bolide BN-NVR/NX User Manual preview
Bolide BN-NVR/NX
Brand: GSA Pages: 101
FOLSOM Blend PRO BP-2002 Installation And Operator'S Manual preview
Blend PRO BP-2002
Brand: FOLSOM Pages: 89
BenQ QCast User Manual preview
QCast
Brand: BenQ Pages: 38
ebm-papst K3G630-FL98-02 Operating Instructions Manual preview
K3G630-FL98-02
Brand: ebm-papst Pages: 13
ARX LSP-1 Owner'S Manual preview
LSP-1
Brand: ARX Pages: 4
Johnson Controls MS-NAE5510-3 Installation Manual preview
MS-NAE5510-3
Brand: Johnson Controls Pages: 28

Brands by name

Popular brands

Load more brands