manualshive.com logo in svg

Analog Devices ADSP-21261 SHARC, Hardware Reference Manual, Page: 451 / 846

Share
Download
Analog Devices ADSP-21261 SHARC Hardware Reference Manual Download Page 451

ADSP-2126x SHARC Processor Hardware Reference

10-15 

 

Serial Peripheral Interface Port

When enabled as a master, the DMA engine transmits or receives data as 
follows:

1. If the SPI system is configured for transmitting, the DMA engine 

reads data from memory into the SPI DMA FIFO. Data from the 
DMA FIFO is loaded into the 

TXSPI

 register and then into the 

Transmit Shift register. This initiates the transfer on the SPI port.

2. If configured to receive, data from 

RXSPI

 is automatically loaded 

into the SPI DMA FIFO, the DMA engine reads data from the SPI 
DMA FIFO and writes to memory. Finally, the SPI initiates the 
receive transfer.

3. The SPI generates the programmed signal pulses on 

SPICLK

 and 

simultaneously shifts data out of 

MOSI

 and shifts data in from 

MISO

.

4. The SPI continues sending or receiving words until the SPI DMA 

word count register transitions from 1 to 0.

If the DMA engine is unable to keep up with the transmit stream during a 
transmit operation because the IOP requires the IOD (I/O data) bus to 
service another DMA channel (or for another reason), the 

SPICLK

 stalls 

until data is written into the 

TXSPI

 register. All aspects of SPI receive oper-

ation should be ignored. The data in the 

RXSPI

 register is not intended to 

be used, and the 

RXS

 (bits 28–27 and 31–30 in the 

SPCTLx

 register) and 

SPISTAT

 bits (bits 26 and 29) should be ignored. The 

ROVF

 overrun condi-

tion cannot generate an error interrupt in this mode.

If the DMA engine cannot keep up with the receive data stream during 
receive operations, then 

SPICLK

 stalls until data is read from 

RXSPI

. While 

performing a receive DMA, the processor core assumes the transmit buffer 
is empty. If 

SENDZ

 = 1, the device repeatedly transmits 0’s on the 

MOSI

 pin. 

Summary of Contents for ADSP-21261 SHARC















































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments