manualshive.com logo in svg

Analog Devices ADSP-21261 SHARC, Hardware Reference Manual

The Analog Devices ADSP-21261 SHARC is a powerful digital signal processor designed specifically for audio applications. Enhance your understanding of this innovative product by accessing its comprehensive Hardware Reference Manual. This invaluable manual can be downloaded for free from manualshive.com, providing you with essential insights and technical guidance.

Share
Download
background image

ADSP-2126x SHARC Processor Hardware Reference

12-15 

 

Digital Audio Interface

Making Connections in the SRU

As described previously, the SRU is similar to a set of patch bays. Each bay 
routes a distinct set of outputs to compatible inputs. These connections 
are implemented as a set of memory-mapped registers with a bit field for 
each input. The outputs are implemented as a set of bit encodings. Con-
ceptually, a patch cord is used to connect an output to an input. In the 
SRU, a bit pattern that is associated with a signal output (shown as item 1 
in 

Figure 12-11

) is written to a bit field corresponding to a signal input 

(shown as item 2 in 

Figure 12-11

).

The memory-mapped SRU registers are arranged by groups, referred to as 
Group A through Group F and described in 

“Signal Routing Unit Regis-

ters” on page A-113

. Each group has unique encodings for its associated 

output signals and a set of Configuration registers. For example, Group A 
is used to route clock signals. Four memory-mapped registers, 

SRU_-

CLK[3:0]

, contain 5-bit wide fields corresponding to the clock inputs of 

various peripherals. The values written to these bit fields specify a signal 
source that is an output from another peripheral. All of the possible 
encodings represent sources that are clock signals (or at least could be 
clock signals in some systems). 

Figure 12-11

 diagrams the input signals 

that are controlled by the Group A register, 

SRU_CLK0

. All bit fields in the 

SRU Configuration registers correspond to inputs. The value written to 
the bit field specifies the signal source. This value is also an output from 
some other component within the SRU.

Note that the lower portion of the patch bay in 

Figure 12-11

 is shown 

with a large number of ports to reinforce the point that one output can be 
connected to many inputs. The same encoding can be written to any num-
ber of bit fields in the same group. It is not possible to run out of patch 
points for an output signal.

Summary of Contents for ADSP-21261 SHARC















































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for ADSP-21261 SHARC

LAWO edge User Manual preview
edge
Brand: LAWO Pages: 154
Radwin Transportation FiberinMotion Deployment Manual preview
Transportation FiberinMotion
Brand: Radwin Pages: 122
Lanner NCA-2510 Installation Manual preview
NCA-2510
Brand: Lanner Pages: 2
Usr USR4504 Installation Manual preview
USR4504
Brand: Usr Pages: 2
ZALMAN CNPS6500B-AlCu User Manual preview
CNPS6500B-AlCu
Brand: ZALMAN Pages: 4
Waves MaxxBCL Manual preview
MaxxBCL
Brand: Waves Pages: 41
ZyXEL Communications GS3700 Series Handbook preview
GS3700 Series
Brand: ZyXEL Communications Pages: 215
Variscite VAR-SOM-MX8M-PLUS Quick Start Manual preview
VAR-SOM-MX8M-PLUS
Brand: Variscite Pages: 2
ETAS XETK-S21.0B User Manual preview
XETK-S21.0B
Brand: ETAS Pages: 68
Intel G6950 Documentation Update preview
G6950
Brand: Intel Pages: 51
Dinstar UC8000 IPPBX User Manual preview
UC8000 IPPBX
Brand: Dinstar Pages: 103
ICP DAS USA VEX-112 Quick Start Manual preview
VEX-112
Brand: ICP DAS USA Pages: 8
TECO e-chill 1 Instruction Manual preview
e-chill 1
Brand: TECO Pages: 24
iTON ID6ZFN-BK0 User Manual preview
ID6ZFN-BK0
Brand: iTON Pages: 12
Multitech FaxFinder FF-120 Administrator User Manual preview
FaxFinder FF-120
Brand: Multitech Pages: 20
Lenovo px Series Quick Start Manual preview
px Series
Brand: Lenovo Pages: 44
Lenovo EMC2 px Series Quick Start Manual preview
EMC2 px Series
Brand: Lenovo Pages: 40
Lenovo LENOVOEMC PX4-300D Specifications preview
LENOVOEMC PX4-300D
Brand: Lenovo Pages: 4

Brands by name

Popular brands

Load more brands