Analog Devices ADSP-21261 SHARC Hardware Reference Manual Download Page 806 | Manualshive

Page: 806 / 846

background image

G-6

ADSP-2126x SHARC Processor Core Manual

Interleaved data.

To take advantage of the DSP’s data accesses to 4- and

3-column locations, programs must adjust the interleaving of data into
(not necessarily sequential) memory locations to accommodate the mem-
ory access mode.

Internal memory space.

This space ranges from address 0x0000 0000

through 0x0005 3FFF (Normal word). Internal memory space refers to
the DSP’s on-chip SRAM and memory mapped registers.

Interrupts.

Subroutines in which a runtime event (not an instruction)

triggers the execution of the routine.

JTAG port.

This port supports the IEEE standard 1149.1 Joint Test

Action Group (JTAG) standard for system test. This standard defines a
method for serially scanning the I/O status of each component in a
system.

Jumps.

Program flow transfers permanently to another part of program

memory.

Length registers.

A length registers is a Data Address Generator (DAG)

register that sets up the range of addresses a circular buffer.

Level-sensitive interrupts.

The DSP detects this type of interrupt if the

signal input is low (active) when sampled on the rising edge of CLKIN.

Loops.

One sequence of instructions executes several times with zero

overhead.

McBSP, Multichannel buffered serial port.

See Serial port.

MCM, Multichannel mode.

See Multichannel mode on

.

Memory Access Modes.

The DSP supports Asynchronous external mem-

ory space. In asynchronous access mode, the DSP’s RD and WR strobes
change before CLKIN edge. In synchronous access mode, the DSP’s RD
and WR strobes change on CLKIN edge.

«
...
804
805
806
807
808
...
»

Summary of Contents for ADSP-21261 SHARC















































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for ADSP-21261 SHARC

Brand: Amperes Pages: 8

Brand: Freescale Semiconductor Pages: 921

Brand: Orban Pages: 255

Brand: Commell Pages: 9

DIRECTOR PRO series

Brand: MF DIGITAL Pages: 79

Brand: Cypress Semiconductor Pages: 33

FastTrak TX4000

Brand: Promise Technology Pages: 76

PSoC 4 S Series

Brand: Cypress Pages: 4

Brand: Uniflair Pages: 24

Brand: National Instruments Pages: 56

Brand: Aleratec Pages: 16

Brand: Carrier Pages: 18

Brand: Qvis Pages: 233

6026 Lapbank 16 mini

Brand: Loxit Pages: 2

Brand: Infoblox Pages: 44

NetStructure ZT 5085

Brand: Intel Pages: 106

Brand: artisan Pages: 36

Firebox T85-PoE

Brand: Watchguard Pages: 27

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands