manualshive.com logo in svg

Analog Devices ADSP-21261 SHARC, Hardware Reference Manual

The Analog Devices ADSP-21261 SHARC is a powerful digital signal processor designed specifically for audio applications. Enhance your understanding of this innovative product by accessing its comprehensive Hardware Reference Manual. This invaluable manual can be downloaded for free from manualshive.com, providing you with essential insights and technical guidance.

Share
Download
background image

ADSP-2126x SHARC Processor Hardware Reference

1-11 

Introduction

PM bus for transfers). Using the DM bus and PM bus in this way, with 
one dedicated to each memory block, assures single-cycle execution with 
two data transfers. In this case, the instruction must be available in the 
cache. The processor also maintains single-cycle execution when one of 
the data operands is transferred to or from off-chip, using the processor 
parallel port.

I/O Processor

The ADSP-2126x Input/Output Processor (IOP) manages the SHARC 
processor’s off-chip data I/O to alleviate the core of this burden. Up to 22 
simultaneous DMA transfers (22 DMA channels) are supported for trans-
fers between internal memory and serial ports (12), the input data port 
(IDP) (8), SPI port (1), and the parallel port. The I/O processor can per-
form DMA transfers between the peripherals and internal memory at the 
full core clock speed. The dual-ported architecture of the internal memory 
allows the IOP and the core to access internal memory simultaneously 
with no reduction in throughput.

Serial Ports.

 The ADSP-2126x processor features up to six synchronous 

serial ports that provide an inexpensive interface to a wide variety of digi-
tal and mixed-signal peripheral devices. The serial ports can operate at up 
to up to half of the processor core clock rate with maximum of 50M bits 
per second. Each serial port features two data pins that function as a pair 
based on the same serial clock and frame sync. Accordingly, each serial 
port has two DMA channels and serial data buffers associated with it to 
service the dual serial data pins. Programmable data direction provides 
greater flexibility for serial communications. Serial port data can automat-
ically transfer to and from on-chip memory using DMA. Each of the serial 
ports offers a TDM multichannel mode (up to 128 channels) and supports 

-law or A-law companding. I

2

S support is also provided.

The serial ports can operate with least significant bit first (LSBF) or most 
significant bit first (MSBF) transmission order, with word lengths from 
three to 32 bits. The serial ports offer selectable synchronization and 

Summary of Contents for ADSP-21261 SHARC















































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for ADSP-21261 SHARC

3Com 3CRWEASY96A Quick Start Manual preview
3CRWEASY96A
Brand: 3Com Pages: 8
F5 i5000 Series Platform Manual preview
i5000 Series
Brand: F5 Pages: 72
PairGain PG-FLEX RT FRL-752 Manual preview
PG-FLEX RT FRL-752
Brand: PairGain Pages: 6
B&B Electronics Parallel & Serial Port Checker PPC User Manual preview
Parallel & Serial Port Checker PPC
Brand: B&B Electronics Pages: 4
National Instruments FieldPoint cFP-RTD-122 Operating Instructions Manual preview
FieldPoint cFP-RTD-122
Brand: National Instruments Pages: 15
Velopex Extra-X Quick Start Manual preview
Extra-X
Brand: Velopex Pages: 7
Tandberg Data SUPERLOADER DLT MAGAZINE Quick Start Manual preview
SUPERLOADER DLT MAGAZINE
Brand: Tandberg Data Pages: 6
Intel BLKDP45SG - MB 1333FSB DDR3 1333 Aud+Lan RAID SATA ATX Product Manual preview
BLKDP45SG - MB 1333FSB DDR3 1333 Aud+Lan RAID SATA ATX
Brand: Intel Pages: 86
MSNswitch UIS-322b Quick Installation Manual preview
UIS-322b
Brand: MSNswitch Pages: 2
ICOP Technology BF01 User Manual preview
BF01
Brand: ICOP Technology Pages: 34
LaCie FireWire 800 ExpressCard 34 Quick Install Manual preview
FireWire 800 ExpressCard 34
Brand: LaCie Pages: 24
Nvidia GEFORCE RTX 4090 Quick Start Manual preview
GEFORCE RTX 4090
Brand: Nvidia Pages: 160
Lanner ECA-4027 User Manual preview
ECA-4027
Brand: Lanner Pages: 99
Ciara Horizon D10750 Disassembly Manual preview
Horizon D10750
Brand: Ciara Pages: 14
ADLINK Technology EOS-1200 User Manual preview
EOS-1200
Brand: ADLINK Technology Pages: 108
THOMSON SPEEDTOUCH 110G Setup And User Manual preview
SPEEDTOUCH 110G
Brand: THOMSON Pages: 26
Altera tPad DE2-115 User Manual preview
tPad DE2-115
Brand: Altera Pages: 43
Renesas Emulation Probe M306V8T-EPB User Manual preview
Emulation Probe M306V8T-EPB
Brand: Renesas Pages: 90

Brands by name

Popular brands

Load more brands