manualshive.com logo in svg

Analog Devices ADSP-21261 SHARC, Hardware Reference Manual

The Analog Devices ADSP-21261 SHARC is a powerful digital signal processor designed specifically for audio applications. Enhance your understanding of this innovative product by accessing its comprehensive Hardware Reference Manual. This invaluable manual can be downloaded for free from manualshive.com, providing you with essential insights and technical guidance.

Share
Download
background image

DAI Interrupt Controller

12-28

ADSP-2126x SHARC Processor Hardware Reference

 

DAI Interrupts

There are several registers in the DAI Interrupt Controller that can be 
configured to control how the DAI interrupts are reported to and serviced 
by the core’s Interrupt Controller. Among other options, each DAI inter-
rupt can be mapped either as a high or low priority interrupt in the 
primary interrupt controller, certain DAI interrupts can be triggered on 
either the rising or falling edge of signals, and each DAI interrupt can also 
be independently masked.

Just as the core has its own interrupt latch registers (

IRPTL

 and 

LIRPTL

), 

the DAI has its own latch registers (

DAI_IRPTL_L

 and 

DAI_IRPTL_H

). When 

a DAI interrupt is configured to be high priority, it is latched in the 

DAI_IRPTL_H

 register. When any bit in the 

DAI_IRPTL_H

 register is set 

(= 1), bit 11 in the 

IRPTL

 register is also set and the core services that 

interrupt with high priority. When a DAI interrupt is configured to be 
low priority, it is latched in the 

DAI_IRPTL_L

 register. Similarly, when any 

bit in the 

DAI_IRPTL_L

 register is set (= 1), bit 6 in the 

LIRPTL

 register is 

also set and the core services that interrupt with low priority. Regardless of 
the priority, when a DAI interrupt is latched and promoted to the core 
interrupt latch, the ISR must query the DAI’s Interrupt Controller to 
determine the source(s). Sources can be any one or more of the Interrupt 
Controller’s 32-configurable channels (

DAI_INT[31:0]

). 

For more infor-

mation, see “DAI Interrupt Controller Registers” on page A-167.

Reading the DAI’s interrupt latches clears them. Therefore, the 
ISR must service all the interrupt sources it discovers. That is, if 
multiple interrupts are latched in one of the 

DAI_IRPTL_x

 registers, 

all of them must be serviced before executing an 

RTI

 instruction.

The 

IDP_FIFO_GTN_INT

 interrupt is not cleared when the 

DAI_IRPTL_H/L

 registers are read. This interrupt is cleared automat-

ically when the situation that caused of the interrupt goes away.

Summary of Contents for ADSP-21261 SHARC















































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for ADSP-21261 SHARC

Acconeer A111 User Manual preview
A111
Brand: Acconeer Pages: 32
Magma PE6R4-I Quick Installation Manual preview
PE6R4-I
Brand: Magma Pages: 2
Paradyne Hotwire 5446 Notice preview
Hotwire 5446
Brand: Paradyne Pages: 2
Delta Electronics DTE-20T Instruction Sheet preview
DTE-20T
Brand: Delta Electronics Pages: 1
Telex Communications 2472AA Instruction Manual preview
2472AA
Brand: Telex Communications Pages: 28
Paradyne 7510 DSU Start-Up Instructions preview
7510 DSU
Brand: Paradyne Pages: 10
AYRSTONE AyrMesh IndoorAP Instructions preview
AyrMesh IndoorAP
Brand: AYRSTONE Pages: 2
Caen A 1735 Technical Information Manual preview
A 1735
Brand: Caen Pages: 14
Kaptia Klever Getting Started preview
Klever
Brand: Kaptia Pages: 14
MF DIGITAL 5200 Live Series EventCD Operator'S Manual preview
5200 Live Series EventCD
Brand: MF DIGITAL Pages: 21
Uniflair PCOWeb Instruction Manual preview
PCOWeb
Brand: Uniflair Pages: 24
National Instruments SC-2040 User Manual preview
SC-2040
Brand: National Instruments Pages: 56
Intel 80960KB Manual preview
80960KB
Brand: Intel Pages: 44
SilverStone argon series User Manual preview
argon series
Brand: SilverStone Pages: 16
NUROTRON CS-10A Operation Manual preview
CS-10A
Brand: NUROTRON Pages: 16
Multitech FaxFinder FF-120 Administrator User Manual preview
FaxFinder FF-120
Brand: Multitech Pages: 20
Devolo Kurulum Manual preview
Kurulum
Brand: Devolo Pages: 24
Fujitsu 467 Manual preview
467
Brand: Fujitsu Pages: 36

Brands by name

Popular brands

Load more brands