Altigen ACM 6.5 Administration Manual Download Page 406 | Manualshive

Page: 406 / 502

background image

Limitations

392

MAXCS ACM 6.5 Administration Manual

•

If the board configuration for the default gateway is changed, or the license for the
SIP-Trunk is changed, you must reboot both the primary and secondary systems to
make the change take effect. The correct order for reboot is: 1) shut down inactive

system; 2) shut down active system; 3) start active system; 4) start the inactive
system.

•

HMCP installed with Softswitch is not supported if VLAN is used. This is because to
run HMCP, VLAN needs one additional NIC but redundancy supports only two NICs.

•

If the active system needs to be shut down for maintainance, control must be
manually switched from the active system to the standby system first.

«
...
404
405
406
407
408
...
»

Summary of Contents for ACM 6.5























































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for ACM 6.5

WiFi-Doc Client for iOS

Brand: Mitsubishi Pages: 10

Brand: FARONICS Pages: 4

WINSELECT STANDARD

Brand: FARONICS Pages: 36

Conference Composer

Brand: Polycom Pages: 29

BRIGHTMAIL GATEWAY SMALL BUSINESS EDITION

Brand: Symantec Pages: 4

Brand: Symantec Pages: 30

Brand: FujiFilm Pages: 55

Brand: Oracle Pages: 130

Vigil Server V5.00

Brand: 3xLogic Pages: 134

Brand: Xerox Pages: 308

DEEP FREEZE STANDARD - 1-2010

Brand: FARONICS Pages: 24

Brand: Panasonic Pages: 78

Media Manager for PSP

Brand: GameShark Pages: 15

EzSign TV Editor

Brand: LG Pages: 12

Brand: LG Pages: 26

Brand: LG Pages: 83

Zenith Free-To-Guest

Brand: LG Pages: 28

SuperSign Elite-c

Brand: LG Pages: 36

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands