manualshive.com logo in svg

Altigen ACM 6.5, Administration Manual, Page: 358 / 502

Share
Download
Altigen ACM 6.5 Administration Manual Download Page 358

Setting VoIP Codec Profiles

344

MAXCS ACM 6.5 Administration Manual

 

Name the new profile, and click 

OK

.

Make your changes or additions, and click 

Apply

. These are the fields in the Codec 

configuration window:

Parameter

Description

Codec Profile Table

 

Lists codec profiles by name. Select a profile in the 
table to modify its settings, then click 

Apply

 in the 

panel where you made the changes. 
Click the 

Add

 button to add a codec profile. Click the 

Remove

 button to remove the selected profile. You 

cannot remove the Default profile.

Name

 

Name of the codec profile. You can modify the name, 
and click 

Apply

. The 

Default

 profile name cannot be 

changed.

Codec

 

There are several options: 
• G.711 Mu-Law
• Prefer G.723.1, support G.729
• Prefer G.729, support G.723.1
• G.711 A-Law
• Prefer G.711 Mu-Law, support G.711 A-Law
• Prefer G.711 A-Law, support G.711 Mu-Law

G.711 

provides toll quality digital voice encoding, 

and 

G.723

 and 

G.729 

use low rate audio encoding 

to provide near toll quality performance under clean 
channel conditions. 

G.711/G.723/G.729 
Silence Suppression

 

When silence suppression is enabled, and silence is 
detected during a call, MAXCS stops sending packets 
to the other side. This decreases the bandwidth 
requirement, however the voice quality may be 
degraded slightly. These are system-wide settings.

Summary of Contents for ACM 6.5























































































































































































































































































































































































































































































































Reviews:

No comments