Altigen ACM 6.5 Administration Manual Download Page 323

Page: 323 / 502

Queue Management - Advanced

MAXCS ACM 6.5 Administration Manual 309

Queue Management - Advanced

When

Advanced

is selected on the

Queue Management

tab, the

Setup

button

becomes available.

Figure 12. Workgroup Configuration, Queue Management, Advanced Queue Control

To configure options for advanced queuing control, click the

Setup

button. This opens

the Advanced Queue Management (AQM) application configuration window with tabs for

configuring

Announcement

Menu Selection

, and

Queue Overflow

Announcement

The

Announcement

tab allows for configuration of queue announcements.

Figure 13. Workgroup Configuration, Advanced Queue Management, Announcement tab

Summary of Contents for ACM 6.5























































































































































































































































































































































































































































































































Search results

Summary of Contents for ACM 6.5

Reviews:

Related manuals for ACM 6.5

Brands by name

Popular brands

Altigen ACM 6.5, Administration Manual

Search results

Summary of Contents for ACM 6.5

Reviews:

Related manuals for ACM 6.5

Brands by name

Popular brands