Altigen ACM 6.5 Administration Manual Download Page 172

Page: 172 / 502

Configuring the Triton T1/E1 Board

158

MAXCS ACM 6.5 Administration Manual

Figure 9. T1 PRI Protocol Configuration dialog box (top half)

Figure 10. T1 CAS Protocol Configuration dialog box (top half)

Selecting Span Types

•

T1 CAS—

select this option to associate all channels on the span to T1 CAS.

•

Regular ISDN PRI—

select this option to indicate 23B+D ISDN PRI span and to

designate the last channel as the D channel.

•

Enable Tie Trunk—

check this box to enable a tie trunk. Tie trunks must terminate

to a system also configured as a tie trunk.

Note:

This option not available when

E1 CAS

is selected.

Summary of Contents for ACM 6.5























































































































































































































































































































































































































































































































Search results

Summary of Contents for ACM 6.5

Reviews:

Related manuals for ACM 6.5

Brands by name

Popular brands

Altigen ACM 6.5, Administration Manual

Search results

Summary of Contents for ACM 6.5

Reviews:

Related manuals for ACM 6.5

Brands by name

Popular brands