manualshive.com logo in svg

Altigen ACM 6.5, Administration Manual, Page: 161 / 502

Share
Download
Altigen ACM 6.5 Administration Manual Download Page 161

MAXCS ACM 6.5 Administration Manual 147

C

H A P T E R

12

Board Configuration

This chapter shows how to configure AltiGen telephony boards:

•

Triton Resource Board, page 149

•

Triton 30-Party Conference Board, page 150

•

Triton Analog Station Board, page 150

•

Triton Analog Trunk LS/GS and LS Boards, page 150

•

Triton VoIP Board, page 151

•

Triton T1/E1 Boards, page 152

•

Virtual Boards SIP and H323, page 166

•

Virtual Board HMCP, page 167

•

MAX1000/2000 Board, page 174

•

Virtual MobileExtSP Board, page 175

For information on how to install AltiGen boards, refer to the 

Quick Installation Guide

 

provided with every board package.
Board attributes and functions are accessible from the Boards window.

Summary of Contents for ACM 6.5























































































































































































































































































































































































































































































































Reviews:

No comments