Altigen ACM 6.5 Administration Manual Download Page 72

Page: 72 / 502

Configuring System Speed Dialing

MAXCS ACM 6.5 Administration Manual

Figure 7. System Configuration, System Speed tab

Adding Speed Dial Entries

To add a speed dial entry,
1. Click the

Add

button. The Speed Dial Configuration dialog box appears.

2. The next available ID is filled in for you, or you can select the ID number using the

drop-down arrow.

3. Type in a name for the Speed Dial entry, then enter the full number as you would

dial it, with a maximum of 20 digits per entry. For example, the phone number
914085551212 comprises

(trunk access code),

(long distance prefix), followed

408

(area code), and then the seven-digit telephone number.

Valid digits include

through

, and

(,)

comma.

The comma represents a

one-second pause

, when IP trunks are not used.

Summary of Contents for ACM 6.5























































































































































































































































































































































































































































































































Search results

Summary of Contents for ACM 6.5

Reviews:

Related manuals for ACM 6.5

Brands by name

Popular brands

Altigen ACM 6.5, Administration Manual

Search results

Summary of Contents for ACM 6.5

Reviews:

Related manuals for ACM 6.5

Brands by name

Popular brands