manualshive.com logo in svg

Altigen ACM 6.5, Administration Manual, Page: 489 / 502

Share
Download
Altigen ACM 6.5 Administration Manual Download Page 489

MAXCS ACM 6.5 Administration Manual 475

A

P P E N D I X

D

Technical Support & Product Repair

Services

This appendix describes:

•

AltiGen technical support policy and procedures

•

Product repair

•

Technical training for administrators

Technical Support

Eligibility

: AltiGen provides technical support to Authorized AltiGen dealers and 

distributors only.
End user customers, please contact your Authorized AltiGen Dealer for technical support. 

How To Reach AltiGen Technical Support

Authorized AltiGen dealers and distributors

 may contact AltiGen technical support 

by any of the following methods:

•

You may request technical support on AltiGen’s dealer web site, at https://
dealer.altigen.com. Open a case on this site, and a Technical Support representative 
will respond within one business day.

•

Call 888-ALTIGEN, option 5, or 408-597-9000, option 5,

 

and follow the prompts.

 

Your call will be answered by one of AltiGen’s Technical Support Representatives or 

routed to the Technical Support Message Center if no one is available to answer your 
call. 
Technical support hours are 5:00 a.m. to 5:00 p.m., PT, Monday through Friday, 
except holidays. 
If all representatives are busy, your call will be returned in the order it was received, 
within four hours under normal circumstances. Outside AltiGen business hours, only 
urgent calls will be returned on the same day (within one hour). Non-urgent calls will 

be returned on the next business day.
Please be ready to supply the following information:

•

Dealer ID

•

AltiGen Certified Engineer ID

•

Product serial number

Summary of Contents for ACM 6.5























































































































































































































































































































































































































































































































Reviews:

No comments