Altigen ACM 6.5 Administration Manual Download Page 191

Page: 191 / 502

MAXCS ACM 6.5 Administration Manual 177

H A P T E R

In Call Routing Configuration

In Call Routing rules determine how the system routes incoming trunk calls to various
targets. The system’s routing steps are as follows:

The In Call Routing Configuration window lets you enter Caller ID and DNIS numbers into

a routing table and set routing rules for a matched number.
To configure In Call Routing, select

PBX > In Call Routing Configuration

Step

Routing Process

Match DID number configured in extension, workgroup, or hunt
group. If there is no match, go to the next step.

Match caller ID defined in the Caller ID Routing table. If there is a
match and

•

today is a holiday, route the call according to the Holiday Profile’s
routing rules.

•

today is

not

a holiday, route the call according to business hour

routing rules defined in the Caller ID Routing configuration.

If there is no caller ID match, go to the next step.

Match DNIS number defined in the DNIS Routing table. If there is a
match and

•

today is a holiday, route the call according to the Holiday Profile’s
routing rules.

•

today is

not

a holiday, route the call according to business hour

routing rules defined in the DNIS Routing configuration.

If there is no DNIS number match, go to the next step.

If today is a holiday, route the call according to the Holiday Profile
configured for the trunk port that the call is coming in on. If today
is

not

a holiday, route the call according to the business hours

routing rules defined in the

In Call Routing

tab of the Trunk

Configuration window.

Summary of Contents for ACM 6.5























































































































































































































































































































































































































































































































Search results

Summary of Contents for ACM 6.5

Reviews:

Related manuals for ACM 6.5

Brands by name

Popular brands

Altigen ACM 6.5, Administration Manual

Search results

Summary of Contents for ACM 6.5

Reviews:

Related manuals for ACM 6.5

Brands by name

Popular brands