Altigen ACM 6.5 Administration Manual Download Page 494

Page: 494 / 502

480

MAXCS ACM 6.5 Administration Manual

(Control) Protocol, a transport protocol for real-time applications used to transport
packetized voice packets over the IP network.

5. Check the IP Dialing Table in Enterprise Manager for

Server ID Length

. Refer to

“Defining the IP Dialing Table” on page 352.

6. Check if

Called Extension

is a

Workgroup

or has

Multiple Call Waiting Enabled

When the called party is a workgroup pilot number or has Multiple Call Waiting
enabled, the caller is placed on hold and hears ringback or music.

IP Resource Does Not Appear in Current Resource Statistics

When an IP resource doesn’t appear in the

Current Resource Statistics

window, there

are two possible causes:

•

Device Driver is Not Running

. Check the device driver. Make sure it’s installed

and working properly.

•

Triton VoIP Board is Not Installed Properly

. Refer to the

Quick Installation

Guide

for details on proper installation of the Triton VoIP board.

Summary of Contents for ACM 6.5























































































































































































































































































































































































































































































































Search results

Summary of Contents for ACM 6.5

Reviews:

Related manuals for ACM 6.5

Brands by name

Popular brands

Altigen ACM 6.5, Administration Manual

Search results

Summary of Contents for ACM 6.5

Reviews:

Related manuals for ACM 6.5

Brands by name

Popular brands