manualshive.com logo in svg

Altigen ACM 6.5, Administration Manual, Page: 343 / 502

Share
Download
Altigen ACM 6.5 Administration Manual Download Page 343

Virtual LANs

MAXCS ACM 6.5 Administration Manual 329

The NIC in both the MAXCS server and the IPTalk client (used with MaxCommunicator/
MaxAgent) must support 802.1p. To see if the NIC supports the 802.1p feature, open 

the NIC’s Properties dialog box and select the 

Advanced

 tab. See if the "QoS Packet 

Tagging" property is in the Property list. (Different NICs have different properties and 
may display a different property name for the 802.1p feature.) If the NIC supports the 

802.1p feature, the default value is 

Disabled

 and you can change this value to enable 

802.1p as seen in the following figure: 

Once the 802.1p property is enabled, the operating system should notify the NetFilter 

driver whether the NIC supports the 802.1p feature.
For 802.1p, eight different classes of service are available, expressed through the 3-bit 
user priority field in an IEEE 802.1Q header added to the frame. In MAXCS, 802.1p 
tagging is implemented in the NetFilter driver in the server side applying QoS tagging to 

the voice packet. The IP phone tags the voice packet from the ARM processor with a user 
configured value. 

To specify the priority value

The server side configuration is located in the HMCP board's 

Board Configuration

 

settings or the VoIP board’s 

Board Configuration > Advanced setting

:

In MaxCommunicator/MaxAgent, the configuration is in the IPTalk configuration screen:

Summary of Contents for ACM 6.5























































































































































































































































































































































































































































































































Reviews:

No comments