manualshive.com logo in svg

Altigen ACM 6.5, Administration Manual, Page: 483 / 502

Share
Download
Altigen ACM 6.5 Administration Manual Download Page 483

MAXCS ACM 6.5 Administration Manual 469

Service Parameters/Request Information for PRI

To subscribe to PRI service, certain parameters are required to establish service. The 

information provided below identifies the recommended and supported parameters for 
PRI service. When ordering PRI service, provide the following service request 
information:

Equipment Information

•

PBX Manufacturer—AltiGen Communications, Inc.

•

CSU/DSU—ADTRAN T1 ACE (recommended) or other CSU/DSU

Technical Information for PRI with Voice

Switch Type:

•

5ESS (recommended) 

•

DMS (recommended) 

•

NI-2 (recommended) 

•

4ESS

Framing:

•

Super Frame (SF)/D4

•

Extended Super Frame (ESF) (recommended)

Line Coding:

•

Alternate Mark Inversion (AMI)

•

B8ZS (recommended)

Physical Termination: 

•

RJ-48X or RJ-48C

Wire: 

•

4 wires

PRI Channel Assignment

D Channels Assignment—24th channel (channel ID 23)

Note:

MAXCS can configure any channel in a PRI span to be the D channel. The 

default setting is the last channel. Every span should select a D channel within 
the span. Shared D channel (NFAS) or back up D channel is not supported.

Hunting—Most Idle, Least Idle, Ascend, Descend
DNIS Digits—can be 3 to 10 digits

CSU/DSU Requirements

The CSU (channel service unit) is a device used to connect a digital trunk line coming in 

from the phone company to the PBX. A CSU can terminate signals, repeat signals, and 
respond to loopback commands sent from the central office.

Summary of Contents for ACM 6.5























































































































































































































































































































































































































































































































Reviews:

No comments