manualshive.com logo in svg

Altigen ACM 6.5, Administration Manual

The Altigen ACM 6.5 Administration Manual is a comprehensive guide that provides step-by-step instructions for efficiently configuring and managing your Altigen ACM 6.5 system. This manual is available for free download exclusively from our website manualshive.com, ensuring easy access to this essential resource.

Share
Download
background image

468

MAXCS ACM 6.5 Administration Manual

DNIS, Caller ID:

•

DTMF (Dual Tone Multi-Frequency)

Physical Termination:

•

RJ-48X or RJ-48C

Wire:

•

4 wires

800 Service:

•

You decide

Termination Impedance:

•

100 ohms

Type of Registered Services Provided

•

BN 1.544 Mbps SF without power

•

DN 1.544 Mbps SF B8ZS without power

•

1KN 1.544 Mbps ANSI ESF without power

•

1SN 1.544 Mbps ANSI ESF, B8ZS without power (recommended)

Service Order Code

SOC 6.0P AS.2

T1 Channel Assignment

•

Trunk Type

—

In, Out, or 2-Way (recommended)

•

Channels Assigned

—

24 (Enter partial channels if you wish to subscribe to both voice 

and data service.)

•

Hunting

—

Most Idle, Least Idle, Ascend, Descend

•

DNIS Digits/Signal

—

3/DTMF (can be 3 to 10 digits)

•

Caller ID Signal

—

DTMF, if available (Not every service provider provides Caller ID 

over T1 lines.)

CSU/DSU Requirements

The CSU (channel service unit) is a device used to connect a digital trunk line coming in 
from the phone company to the PBX. A CSU can terminate signals, repeat signals and 
respond to loopback commands sent from the central office.

Summary of Contents for ACM 6.5























































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for ACM 6.5

Xerox DocuPrint 115 System Manual preview
DocuPrint 115
Brand: Xerox Pages: 100
Octel Aria 1.2 Release Manual preview
Aria 1.2
Brand: Octel Pages: 64
R&S FSV-K7 Operating Manual preview
FSV-K7
Brand: R&S Pages: 262
F-SECURE ANTI-VIRUS FOR MICROSOFT EXCHANGE 8.00 - Getting Started Manual preview
ANTI-VIRUS FOR MICROSOFT EXCHANGE 8.00 -
Brand: F-SECURE Pages: 29
Promise Technology FastTrak SX Series Version 4.4 User Manual preview
FastTrak SX Series Version 4.4
Brand: Promise Technology Pages: 102
Red Hat APPLICATION STACK 1.1 RELEASE Release Note preview
APPLICATION STACK 1.1 RELEASE
Brand: Red Hat Pages: 30
Denon DP-200USB Brochure & Specs preview
DP-200USB
Brand: Denon Pages: 2
Adaptec Disk Array Administrator User Manual preview
Disk Array Administrator
Brand: Adaptec Pages: 139
Unibrain API-810 User Manual preview
API-810
Brand: Unibrain Pages: 77
AMX AMXUSBLAN Operation/Reference Manual preview
AMXUSBLAN
Brand: AMX Pages: 24
Tech Source RAPTOR 2500T-DL - RAPTOR OPENWINDOWS FOR SOLARIS INSTALLATION AND Brochure preview
RAPTOR 2500T-DL - RAPTOR OPENWINDOWS FOR SOLARIS INSTALLATION AND
Brand: Tech Source Pages: 2
UNIBLUE DriverScanner 2010 Product Manual preview
DriverScanner 2010
Brand: UNIBLUE Pages: 12
IBC BoilerNet Interface Controller II User Manual preview
BoilerNet Interface Controller II
Brand: IBC Pages: 52
MACROMEDIA 38028779 - Macromedia Dreamweaver - Mac Using Manual preview
38028779 - Macromedia Dreamweaver - Mac
Brand: MACROMEDIA Pages: 582
Nintendo RVLRRFPE Instruction Booklet preview
RVLRRFPE
Brand: Nintendo Pages: 34
IBM Terminal Emulation TN5250 User Manual preview
Terminal Emulation TN5250
Brand: IBM Pages: 51
Tascam TASCAM PCM Recorder Important Notice preview
TASCAM PCM Recorder
Brand: Tascam Pages: 2
Garmin Que Application Manual preview
Que
Brand: Garmin Pages: 33

Brands by name

Popular brands

Load more brands