ABB OmniCore V250XT Page 362 Product Manual Download

Page: 362 / 456

Troubleshooting flowchart

Problem releasing brakes

Check

Module Status LED

on A1

Not lit

Solid green

Check LEDs:

PS, MS, PC, HMI

Abnormal

Solid green (all 3)

Troubleshoot
- robot signal exchange
proxy K2
- power unit
- main computer
- FlexPendant

Check connec!on

from X1 to

manipulator

Connec!on ok

Connec!on not ok

Check connec!on

from T4.X15 to X1

Check connec!on

T4.X13 to A1.X11

Connec!on is ok

Connec!on
not ok

Repair connec!on

Connec!on
not ok

Measure power on

T4.X13/X14

Power is ok

No power

Connec!on is ok

Test the brake

Test the brake release

Brake is ok

Brake not ok

Brake release is ok

Not ok

Contact ABB

Problem solved

Troubleshoot
- brake release on
manipulator
-main computer A2
- robot signal exchange
proxy K2
- power unit A1

Troubleshoot power unit A1

xx2100001142

Continues on next page

362

Product manual - OmniCore V250XT

3HAC073447-001 Revision: B

7 Troubleshooting

7.2.4 Problem releasing the robot brakes

Continued

Summary of Contents for OmniCore V250XT








































































































































































































































































































































































































































































Search results

Summary of Contents for OmniCore V250XT

Reviews:

Related manuals for OmniCore V250XT

Brands by name

Popular brands

ABB OmniCore V250XT, Product Manual

Search results

Summary of Contents for OmniCore V250XT

Reviews:

Related manuals for OmniCore V250XT

Brands by name

Popular brands