ABB OmniCore V250XT Page 252 Product Manual Download

Page: 252 / 456

Note/Illustration

Action

Location of wrist strap button:

ELECTROSTATIC DISCHARGE
(ESD)

The unit is sensitive to ESD. Before
handling the unit read the safety inform-
ation in section

The unit is sensitive to

ESD on page 43

xx2100000318

LEDs on page 383

Verify that the LED

High voltage warning

is not lit.

Removing the power unit

Note/Illustration

Action

Disconnect:

•

A1.X13 - K2.X10

•

A1.X9 - K2.X4

•

A1.X5 - T4.X1

•

A1.X12 - T4.X3

•

A1.X1 - Incoming mains (X0)

xx2100000322

Remove the screws and pull the power
unit out from the two guiding pins on the
mounting plate.

CAUTION

Only the sheet metal on the power unit
can be used for holding.
Do not touch the connectors or the filter
on the power unit.

CAUTION

The weight of the power unit is 13 kg.
Use protective gloves when lifting this
unit.

CAUTION

The cabling is sensitive to mechanical
damage. Handle it with care to avoid
damage to the cabling or the connector,
avoid any kind of tilt or skew.

Continues on next page

252

Product manual - OmniCore V250XT

3HAC073447-001 Revision: B

5 Repair

5.2.9 Replacing the power unit

Continued

Summary of Contents for OmniCore V250XT








































































































































































































































































































































































































































































Search results

Summary of Contents for OmniCore V250XT

Reviews:

Related manuals for OmniCore V250XT

Brands by name

Popular brands

ABB OmniCore V250XT, Product Manual

Search results

Summary of Contents for OmniCore V250XT

Reviews:

Related manuals for OmniCore V250XT

Brands by name

Popular brands