ABB OmniCore V250XT Page 40 Product Manual Download | Manualshive

Page: 40 / 456

background image

Load current

As baseline there is no integrated fuse or circuit breaker. The option 3008-3 Mains
connector/Fuse includes integrated circuit breaker.

Add an external circuit breaker (class K) according to full load current, as marked
on the controller nameplate. The following table shows the recommended rating
for an external fuse or circuit breaker.

Current (A)

Voltage (V)

Robot

3x32 A

380 VAC-480 VAC, 3-phase

IRB 4600

3x32 A

380 VAC-480 VAC, 3-phase

IRB 5710

3x32 A

380 VAC-480 VAC, 3-phase

IRB 5720

3x32 A

380 VAC-480 VAC, 3-phase

IRB 6700

Note

For details about installations according to UL requirements, see

Connecting

incoming mains and protective earth to the controller

chapter in

Product

manual - OmniCore V250XT

.

Residual current

An external earth fault protection (residual current device, RCD) is required based
on the following data:

Residual Current in controller (mA)

Robot

< 30 mA

IRB 4600

< 30 mA

IRB 5710

< 30 mA

IRB 5720

< 30 mA

IRB 6700

Note

The integrator is responsible to address local electrical requirements.

40

Product manual - OmniCore V250XT

3HAC073447-001 Revision: B

© Copyright 2020-2022 ABB. All rights reserved.

2 Controller description

2.2 Technical data for OmniCore V250XT controller

Continued

«
...
38
39
40
41
42
...
»

Summary of Contents for OmniCore V250XT









































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for OmniCore V250XT

Brand: Rethink Robotics Pages: 183

robobrain.LEDgripper

Brand: robominds Pages: 11

Brand: Sphero Pages: 7

Brand: igus Pages: 66

Brand: ESCALADE Pages: 4

Brand: ESCALADE Pages: 34

Tank Mechanical Kit

Brand: OSEPP Pages: 36

Brand: L’EPEE 1839 Pages: 16

Brand: KEYI Pages: 107

Micro:bit Mini Smart Robot Car

Brand: Keyestudio Pages: 132

Smart Little Turtle Robot V3

Brand: Keyestudio Pages: 230

Brand: Keyestudio Pages: 247

Brand: Keyestudio Pages: 249

4WD Bluetooth Multi-functional Car

Brand: Keyestudio Pages: 369

Brand: Denso Pages: 56

Brand: Kwunphi Pages: 40

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands