ABB OmniCore V250XT Page 215 Product Manual Download | Manualshive

Page: 215 / 456

background image

Refitting the connected services gateway

Refitting the connected services gateway

Note/Illustration

Action

DANGER

Before doing any work inside the cabinet,
disconnect the mains power. For more
information, see

Electrical safety on

1

ELECTROSTATIC DISCHARGE
(ESD)

The unit is sensitive to ESD. Before
handling the unit read the safety inform-
ation in section

The unit is sensitive to

2

xx1900002331

Hook up the connected services gateway
to the bracket and push carefully into
position.

Note

During the installation, the gap between
the lower surface of the connected ser-
vices gateway and the upper surface of
the main computer should be zero.

3

Reconnect:

•

K7.X1 - K2.X3

i

•

K7.X2 - A2.X5

4

i

For connected services gateway wired, there is no power cable.

Reconnecting the antenna

Note/Illustration

Action

xx2100001054

Insert the cable from the cable grommet.

1

Continues on next page

Product manual - OmniCore V250XT

215

3HAC073447-001 Revision: B

© Copyright 2020-2022 ABB. All rights reserved.

5 Repair

5.2.5 Replacing the connected services gateway

Continued

«
...
213
214
215
216
217
...
»

Summary of Contents for OmniCore V250XT









































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for OmniCore V250XT

Brand: K-Team Pages: 20

Brand: OMOROBOT Pages: 19

Brand: YASKAWA Pages: 82

Brand: Keenon Robotics Pages: 23

Brand: Keenon Robotics Pages: 28

POLOLU STSPIN220

Brand: Eckstein komponente Pages: 7

Bartendro B007V1

Brand: Party Robotics Pages: 16

Brand: Parallax Pages: 7

Brand: TTS Pages: 3

Brand: TTS Pages: 16

Brand: Vincross Pages: 132

Brand: Denso Pages: 70

Brand: Denso Pages: 112

Brand: Denso Pages: 120

RoboMaker X5 DROID

Brand: Clementoni Pages: 29

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands